How to debug horizontal insulating glass two-component gluing machine

卧式中空玻璃双组份打胶机放在一个平整干净的平面上，连接电源和气源，两者确认接通之后就开始进行操作。

Place the horizontal insulating glass two-component gluing machine on a flat and clean plane, connect the power supply and air source, and start the operation after they are confirmed to be connected.

首先打开气泵开关，电源总开关，控制台开关，在控制台按手动按钮，然后在显示屏上找到原点设定，点击辅助原点设定，然后点击头部原点设定，注意原点设定时避免头部和辅助吸盘碰撞。

First turn on the air pump switch, the main power switch and the console switch, press the manual button on the console, then find the origin setting on the display screen, click the auxiliary origin setting, and then click the head origin setting. Pay attention to avoid collision between the head and the auxiliary suction cup when setting the origin.

等设定好然后返回找到玻璃厚度设定，先是玻璃的厚度然后是铝隔条然后还是玻璃的厚度，输入完以后，点击设置进入。等命令位置和当前位置数值一致即可，注意设置时传送带上不要有玻璃。

After setting, go back to find the glass thickness setting, first the glass thickness, then the aluminum spacer, and then the glass thickness. After entering, click the setting to enter. Wait until the command position is consistent with the current position value. Note that there is no glass on the conveyor belt during setting.

然后是混交了，按桶胶按钮，按工作选择按钮，然后按拍胶启动，在按伐开，此时胶头以出胶，等看不见白胶，以混均匀以后按伐关，再按链接生产线，自动运行，此时可以自动打胶。

Then it is mixed. Press the first bucket of glue button, press the work selection button, and then press the glue shooting button to start. After pressing the cutting open, the glue head will release the glue. When the white glue is not visible, press the cutting off after mixing evenly, and then press the link production line to run automatically. At this time, the glue can be applied automatically.

调试的注意事项：

Precautions for commissioning:

1、在当天机器操作完毕后要把胶管内的胶冲出，防止硬化；如果长时间不实用要注意用煤油清洗胶管和胶枪。

1. After the operation of the machine on the same day, the rubber in the rubber hose shall be washed out to prevent hardening; If it is not practical for a long time, pay attention to cleaning the hose and gun with kerosene.

2、双组份打胶机使用的硅酮胶或聚硫胶要注意杂质不能过高，低质量的胶容易堵塞胶管的过滤系统，造成出胶不畅或不均匀。

2. For the silicone glue or polysulfide glue used in the two-component gluing machine, attention shall be paid to that the impurities shall not be too high. The low-quality glue is easy to block the filtering system of the hose, resulting in poor or uneven glue delivery.

3、在更换胶的品种时要特别注意把双组份打胶机内残留的胶冲净，更好清洗，因为不同品种甚至品牌的胶容易反应堵塞机器。

3. When changing the type of glue, pay special attention to flush the residual glue in the two-component gluing machine, and it is best to clean it, because the glue of different types and even brands is easy to react and block the machine.

4、液压站系统的压力，不能调的太高，要根据室内环境温度等实际情况，调至满足胶嘴正常出胶均匀打胶即可。打开液压站时一定要打开胶枪，否则B组份管路压力将升得很高，造成安全事故。

4. The pressure of the hydraulic station system cannot be adjusted too high. According to the actual situation such as indoor ambient temperature, adjust it to meet the normal glue output of the glue nozzle and apply glue evenly. When opening the hydraulic station, be sure to open the glue gun, otherwise the pressure of component B pipeline will rise very high, resulting in safety accidents.

以上内容就是关于双组份打胶机http://www.bwhcul.com/的介绍，希望这些内容对大家有所帮助。如果您还有什么疑问,或者想要了解更多资讯欢迎咨询我们官网。我们将竭诚为您服务。

The above content is about the two-component gluing machine http://www.bwhcul.com/ I hope these contents will be helpful to you. If you have any questions or want more information, please consult our official website. We will serve you wholeheartedly.