为了更好的使用打胶机进行工作，相关的问题应该多来了解，比如双组份打胶机流速慢或直接打不出胶来的原因有哪些呢？下面小编为您简单讲解一番。

In order to better use the glue dispenser for work, we should learn more about relevant problems. For example, what are the reasons for the slow flow rate of two-component glue dispenser or the direct failure to produce glue? Here's a brief explanation.

打胶机流速慢：

Slow flow rate of sealant applicator:

1）B组分有杂质：B组份在生产、运输或储存过程中如果操作不当或者存放不好，与空气接触易产生颗粒。

1) Impurities in component B: if component B is improperly operated or stored during production, transportation or storage, it is easy to produce particles when contacting with air.

2）工人施工不当：

2) Improper construction by workers:

①更换B组分时需要先排气，排出来的B组分堆积在压盘上，由于B组分压盘只有一根杆，在往下压的过程中会不断晃动，压盘上固化的B组分会掉入新桶内。固化的B组分经压力后会分散成小颗粒，导致堵枪;②混合器和过滤网没有经常清理;

① When replacing component B, it is necessary to exhaust first. The discharged component B is stacked on the pressure plate. Since the component B pressure plate has only one rod, it will shake continuously during the downward pressure process, and the solidified component B on the pressure plate will fall into the new barrel. The solidified component B will disperse into small particles after pressure, resulting in gun plugging; ② The mixer and filter screen are not cleaned frequently;

打胶机不出胶：

Glue does not come out of the gluing machine:

1，检查气源是否在0.6至0.8Mpa之间；

1. Check whether the air source is between 0.6 and 0.8Mpa;

2，检查触摸屏中编辑功能菜单中的密封不使用是否打开；

2. Check whether the seal is opened in the edit function menu of the touch screen;

3，检查气动开关是否阻塞；

3. Check whether the pneumatic switch is blocked;

4，检查黑胶气动开关与电磁阀动作是否正常；

4. Check whether the black glue pneumatic switch and solenoid valve operate normally;

5，检查比例泵上的智能压力表是否报警，范围在7-35Mpa；

5. Check whether the intelligent pressure gauge on the proportional pump alarms, and the range is 7-35Mpa;

6，检查液压站是否有压力，如无压力：1）清洗比例溢流阀2）检查比例控制器是否通电或松动；

6. Check whether there is pressure in the hydraulic station. If there is no pressure: 1) Clean the proportional overflow valve; 2) Check whether the proportional controller is energized or loose;

7，清洗时是否能出白胶，如不出再检查313胶管、旋转接头是否阻塞；

7. Check whether white glue can be released during cleaning, and if not, check whether 313 rubber tube and rotary joint are blocked;

8，检查一组比例泵下限传感器IB233是否有信号，检查二组比例泵IB407是否有信号；

8. Check whether there is signal from lower limit sensor IB233 of one group of proportional pumps and whether there is signal from IB407 of two groups of proportional pumps;

9，手动检查扫描仪数值是否有正常。

9. Manually check whether the scanner value is normal.

双组份打胶机流速慢或直接打不出胶来是怎么回事？这几个条件缺一不可。你可逐一检查这些方面。更多相关打胶机设备的信息可以随时来我们网站http://www.bwhcul.com进行咨询！

What's wrong with the slow flow rate of the two-component glue dispenser or the direct failure to make glue? These conditions are indispensable. You can examine these aspects one by one. More information about the glue dispenser can be found on our website at any time http://www.bwhcul.com Consult!